ESA Science & Technology - Delivery of Gaia's primary mirrors

Gaia will carry two identical telescopes, each fitted with four mirrors (M1 to 4). A further two mirrors (M5 and 6) will send the light from these dual instruments into the same focal plane. To date, six of the 10 rectangular mirrors have been delivered. They are: the M3A tertiary mirror, whose dimensions are 0.65 x 0.275 m; both of the M4 combiner mirrors (dimensions 0.19 x 0.07 m), and the M5 and M6 mirrors (dimensions 0.54 x 0.36 m), in addition to the M1A primary mirror (dimensions 1.49 x 0.54 m).

One of Gaia's two primary (M1) mirrors. Image courtesy of Sagem, France

All of the mirrors have been fabricated from blanks made of sintered silicon carbide (SiC), a relatively new material in mirror fabrication for space missions. The blanks were made by Boostec in France. Silicon carbide was selected because it allows each mirror to be extremely strong and rigid, but lightweight and with a high thermal conductivity - important not only for its on-orbit performance, but also for minimising deformations caused by Earth's gravity during ground testing.

Each primary mirror is shaped by the French company Sagem (located close to Paris), using computer-guided milling and polishing machines, and weighs about 40 kg. To achieve sufficient smoothness, all of the mirror blanks were coated with a thin layer of silicon carbide by chemical vapour deposition before polishing started. This process was carried out by Schunk Kohlenstofftechnik in Heuchelheim, Germany. The polishing is a slow, painstaking process which requires each mirror to be polished to a precision of about 10 nanometres RMS. To appreciate this technical achievement one can consider that if the Gaia M1 mirror was scaled to the size of the Atlantic ocean, any bumps on the surface would be of the order of a few centimetres.

The mirrors also have an unusual curved shape, which is calculated using a very precise mathematical formula so that there will be no distortion of the incoming light across the telescopes' field of view and at all wavelengths from blue to red.

After polishing, the surface is coated with enhanced silver reflective coating. This coating involves the addition of a dielectric amplification layer, which protects the silver from tarnishing and enhances its reflectivity across the entire spectral range (320 – 1000 nanometres) to be studied by Gaia.

"The mirrors are being integrated on the structural payload module in order to complete the optical train and enable testing to begin," said Matthias Erdmann, ESA's Gaia payload system engineer. "Their shape and size were determined by the room available within the payload fairing of the Soyuz-Fregat launcher."

"The M1 mirrors have a collecting area about 11 times bigger than the primary mirror of its predecessor, ESA's Hipparcos astrometry spacecraft, enabling them to collect many more photons," said Jos de Bruijne, Deputy Project Scientist for Gaia.

"The combination of size, smoothness and special shape is required to provide a wide angle of view - about 0.7 degrees - and a small wave front error that will give extremely sharp images of a billion stars in our Galaxy."

Illustratrion of the Gaia payload module indicating the location of the M1 mirrors. Credit: ESA

Contacts

Matthias Erdmann
Gaia Payload System Engineer
Science Projects Department
Directorate of Science & Robotic Exploration, ESA, The Netherlands
Email: matthias.erdmannesa.int
Phone: +31 71 56 58885

Giuseppe Sarri
Gaia Project Manager
Science Projects Department
Directorate of Science & Robotic Exploration, ESA, The Netherlands
Email: giuseppe.sarriesa.int
Phone: +31 71 565 4966

Jos de Bruijne
Deputy Gaia Project Scientist
Research & Scientific Support Department
Directorate of Science & Robotic Exploration, ESA, The Netherlands
Email: jdbruijnrssd.esa.int
Phone: +31 71 565 5989

Timo Prusti
Gaia Project Scientist
Research & Scientific Support Department
Directorate of Science & Robotic Exploration, ESA, The Netherlands
Email: tprustirssd.esa.int
Phone: +31 71 565 4794